Showing posts with label water desalination. Show all posts
Showing posts with label water desalination. Show all posts

Wednesday, May 18, 2011

OGPSS - American stripper well production

The Total (oil company) discussion on Enhanced Oil Recovery has an illustrative graph to explain why there is a growing need to get as much of the oil in a reservoir as can be economically recovered.



When the large flows of oil that I have written about previously stopped flowing from the major production fields in the on-shore United States, that did not mean that the wells from which they issued were immediately shut-in. Rather, in many cases, although the driving pressure to move the oil to the ground surface had largely disappeared, there was still a sufficient imbalance within the reservoir that oil would flow to the well. And so, before moving on to discuss other fields, I thought I would spend this space covering the pump jacks or “nodding donkeys” that dot the landscape over many of the older oilfields of the United States (and elsewhere).

These “stripper” wells that remove the final volumes of oil from a reservoir make up by far the largest number of wells, by category, that produce within the USA. The EIA reported that there were 363,459 producing oil wells in the USA in 2009. Of these 35.1% produced 1 bbl/day (bd) or less, and 78.7% (a total of 286,109) produced less than 10 bd. For Texas alone, the EIA reports that there are 141,582 wells, and 79.4% of these produce less than 10 bd. (H/t Joules Burn).

So when oil production gets this low, and intermittent, how does the owner get the oil out? The short and simple answer is that the oil is pumped out. And if the well is running slowly, then the pump won’t run all the time, but rather intermittently depending on how fast the pump fills. The original pumpjack design was put together in 1925 by Walter C Trout, and provided the basic design for the units still dotting the American landscape.

Parts of a pumpjack (Lufkin catalog).

That basic design has largely remained the same, but the instrumentation and controls have grown more sophisticated over the years. A baseline estimate of the power requirement is that it needs around 0.2 kwh/bbl/1000 ft to lift the oil to the surface. (Which is quoted as being about a 66% efficiency). Deeper wells are reported to require from 0.27 to 0.81 kwh/bbl/1000 ft. And if the wells are 4,500 ft deep that can give an electricity bill of up to $2,000. (H/t to Joulesburn for raising the topic). Part of the problem and loss in efficiency comes from the need to start and stop the pump, because of the low flow of oil into the well.

The Web site dealing with Stripper wells (those defined as producing below 10 bd) notes:
In the United States of America, one out of every six barrels of crude oil produced comes from a marginal oil well, and over 78 percent of the total number of U.S. oil wells are now classified as such. There are over 400,000 of these wells in the United States, and together they produce nearly 900 thousand barrels of oil per day, 15 percent of U.S. production.
The average stripper produces around 2.2 bd (ibid). (The 25-minute movie “Independent Oil: Rediscovering America's Forgotten Wells” can be obtained from Amazon, or by dropping a note to the Stripper Well Consortium.

Further it points out the economic factors that inhibit re-starting these wells once they are abandoned.
When marginal wells are abandoned, significant quantities of oil remain behind-- sometimes as much as 1/2 to 2/3 of the total oil. In many instances, the remaining reserves are not easily accessible when oil prices subsequently rise again: When marginal fields are abandoned, the surface infrastructure - the pumps, piping, storage vessels, and other processing equipment - is removed and the lease forfeited. Since much of this equipment was probably installed over many years, replacing it over a short period should oil prices jump upward, is enormously cost prohibitve.
The site notes that between 1994 and 2003 some 142,000 wells were plugged and abandoned, losing the remaining oil that they might have produced. This oil is sufficiently important (since it makes up about 10 - 20% of the domestic oil production, depending on what is counted) that DOE has a program dealing with Stripper Well Revitalization (covered on CNN here) and funds The stripper well consortium that investigates ways of improving the technology.

Many of the advances have focused on improving the pumping systems used in these old wells, since the old conventional plunger system are not that efficient, relative to the new units. The large number of wells means that even where these improvements are significant, it will take some period of time to get enough new units into the field to have a significant impact on overall production.
The Gas Operated Automatic Lift (GOAL) PetroPump developed by Brandywine Energy & Development Company. The pump removes fluid from the wellbore more consistently than currently available plunger lift systems. Test results on wells in New York showed a 1.5 to 2.3-time increase in gas yield using the GOAL PetroPump over other casing plunger- type tools. The tool is inexpensive to operate because it requires no external energy source and limited manpower.
One area that they have just started work on involves the use of high-pressure jetting for drilling laterals, with the work being developed by Buckman Jet Drilling Inc. Since I jet drilled my first lateral of this type back some 30-odd years ago and have some considerable familiarity with both the promises of the technology, and some of the problems and other issues that have arisen, I suspect that I will be following this in a bit more detail than I usually allow. But that too will come in a future post, for the moment I will note that, having watched the promotional video I do have some significant concerns that arose out of an earlier incident where a somewhat similar technology was claimed to be able to achieve considerable improvements in well production. In that case my concerns were expressed in Federal Court.

One other recent breakthrough that they have highlighted recently involves the conversion of the significant amounts of water than come from these stripper wells, but which is often brackish, and thus difficult to dispose of, into water of potable quality (i.e. you can drink it). In a slide presentation by Texas A&M, who developed the membrane technology used, the resulting water is compared with Evian, Perrier and similar commercial products. Given the problems that Texas is currently facing with drought this could well solve two problems at one time. Further by lowering the cost of water disposal it, like other SWC developments, can encourage the economies of these small producers and sustain their production further into the future.

Each well may not contribute much, but in the aggregate even small changes can add up, when the totality of the wells affected runs into the hundreds of thousands. This improvement in the tail of well production, sadly, is only likely to be viable in the relatively small on-shore wells and close off-shore where the costs of maintaining the infrastructure above the well is minimal. Once those costs become significant it becomes more difficult to make the economics of the process work.

I’ll talk about some of the other ideas for stimulating these wells in a post somewhat later in the series. But this, from Total, is one I have written about before.



Read more!

Friday, April 22, 2011

Drought, renewable energy, Texas, London and Florida

The Governor of Texas has asked the denizens of the state to pray for rain. The state has not had serious rain for months, and the drought conditions have turned severe.

The current drought conditions in Texas.

Conditions are not anticipated to get any better in the next few months. The recent predictions are that the conditions will persist in the area through July.

Predictions of the weather changes through July (NOAA )

Droughts around the world are one of the unfortunate consequences of changing weather, in much the same way as we have seen high snowfalls in other parts of the country this past winter. There will likely be cries about the underlying causes (with folks forgetting that droughts have occurred throughout history), but this post was started because of a potential event-changing occurrence.

This week Thames Water, which supplies 687 million gallons of water a day to the inhabitants of London and the immediate vicinity, was running its first water desalination plant. The region has faced droughts in the recent past as have other regions of the United Kingdom. Earlier solutions included building large water reservoirs, that at Kielder is the largest man-made reservoir in Europe. There is, however, only a certain limited amount of land that can be made available for this use, and so desalination proves an alternate way of supplying the increasing global demand for water.

In the United States droughts have threatened the viability of nuclear power stations, since the shortage of cooling water (as we recently learned again in Japan) is essential to safe plant operation. And therein lies one of the rubs to the situation. As the spokesman for Thames Water noted, the intent is not just to run the plant when there is a drought, since that is going to be too late. Rather at times of lower rainfall the plant (which can produce up to 150 million gallons a day) will pump clean water into the reservoirs, maintaining their integrity, and building up a reserve that will reduce the drought impact if it occurs. The plant was apparently completed last June at which time it was expected that it would just be used in times of drought. Within the last year that thinking has changed, and the plant is now running intermittently, partly to train operational staff, partly potentially also to help meet demand.
According to the Environment Agency, average water use is 148L per person per day in the UK and in the south-east of England it’s as high as 170L (far higher than the government target of 130L). Despite the popular perception of London as an overcast, rain-soaked city, its rainfall rate is, in fact, on a par with Rome, Dallas and Istanbul.

Schematic of the flow path through the desalination plant.

One question that I had relates to the amount of power that will be needed at Beckton. A calculation assuming that it takes 4 kWh to produce a cubic meter of fresh water, suggests that it will need a 21 MW plant. In 2009 the company CEO noted
The (20 MW) plant will be the first in the world to generate all its energy on-site, from renewable sources, including recycled cooking oil.
However the plant has been controversial, not least because although planning to use rapeseed oil, it could also burn palm oil, which is apparently cheaper. That is much more controversial. Planning permission for a second plant nearby at Southall, was refused in June 2010.

Biofuel powered stations in the UK, which includes that in the Tees Valley, where a plant burning 300,000 tons of recycled wood and specially grown wood from plantations, have had a somewhat mixed reception.

But to get back to the original idea of desalination, the largest plant in the United States is in Tampa with a maximum projected size of 35 million gallons/day, though it currently only produces some 25 million, sufficient for 10% of the region’s water needs. It went on line in 2008.
The plant uses about 44 million gallons per day (mgd) of seawater from a nearby power plant’s cooling system, which is pretreated with sand filters and a diatomaceous earth filtration system to remove particles. Reverse osmosis filters then separate 25 mgd of freshwater from the seawater. The unused concentrated seawater is diluted with up to 1.4 billion gallons of cooling water before it is discharged to the bay and that dilution is why environmental studies show no measurable salinity change in Tampa Bay related to plant production.
Which brings us back to Texas. In the latest report on desalination in the state, two possible developments are cited. There is a plan to install a 2.5 million gallon a day plant at Brownsville and a 1 million gallon a day facility on South Padre Island. Unfortunately the South Padre Island initiative failed in a bond election last year, and its future is considered doubtful. Meanwhile the Brownsville Public Utilities Board is considering combining a renewable energy source (shades of the UK) into the plant, in order to leverage funding, and possibly qualify for DOE funds.

But in the meantime, as the discussion continues, the drought gets worse. The discussions started with an initiative in 2002. As those in Texas may find out the hard way, waiting until the crisis is upon them makes it too late to construct the solution that might have helped. It appears that those in the UK and Florida were just a little more prescient. It might be noted that the initial planning for the Florida plant started in 1996.

Read more!